Kee Safety Kee Anchor Point, fall protection, WEIGHTANKA 08 - 2Kee Anchor non-penetrating anchor point system. Can be used for fall restraint and fall arrest. Suitable for two tie person tie off if used for fall restraint. Suitable for one tie off if used for fall arrest.Weightanka is a mobile, deadweight anchor device for use on roofs up to 5 degrees pitch, where the installation of collective protection or permanent anchor devices is not viable. Weightanka uses a central pedestal which allows the attachment of a safety harness and lanyard and raises the height at which the arrest force is applied. Weightanka can be used on inclined roofs as well as flat roofs. It can also be used on industrial steel cladded pitched roofs when positioned opposite to where the work takes place. This should be used when the roof has a pitch greater than 5°, up to 15°. Rubber-coated base weights are supplied with suction cups which applies additional friction to the roof membrane, further reducing any movement during a fall arrest event. There are also over 100 suction cups moulded to each rubber bonded weight to maximize grip.Kee Safety recommends that whenever possible the Kee Anchor Weightanka is used in "Fall Restraint". This feature restricts anyone from getting close to the edge of the building and consequently, it is not possible for a fall to occur.AdaptableEngineered for all roof types including pitched metal profile and standing seam roofs up to a 35° slope.Modular and VersatileCan be used in conjunction with other products to provide a complete fall protection plan.Easy to installIt’s simply installed with hand tools so there’s no need to buy additional equipment.Safety FirstRest assured that the Weightanka meets all of the requirements of the relevant standards and is safe to use.Specifications:Non-penetrating tie-off solutionConforms to OSHA 1926.502(d)(15)Third party testedPortable component based design –no piece weighs more than 50LbsAllows 2 users in fall restraintFast Install: Complleted in 20 minutes
Kee Safety Kee Kwik Extention Kit Railing system, Kwik SEKee Corner Kwik Kit, Guardrail in a box. Includes (1) middle upright, and (2) 6’ horizontal rails. Meets OSHA and IBC requirements. Visually appealing Rails powder-coated Safety Yellow, fittings galvanized. Highly corrosive resistant. Minimizes downtime in production environments.Quickly protect workplace areas and provide a safe environment with the Kwik Kit® railing. There is no need to weld or bend tubing because the pre-assembled uprights make installation speedy and simple. Safety Yellow coating comes standard, making the railing highly visible.Install the Kwik Kit® using a standard hex key to tighten the large, easy-to-use set screws. This simple hand tool is essentially all you need to create a sturdy railing system – there’s no welding or threading. And because your uprights are pre-assembled, installation is fast. By using a combination of our straight, corner and extension kits, you can achieve almost any standard railing configuration. Rails can also be cut where shorter sections are required and are available in both galvanized steel and aluminium. The safety yellow coating makes the Kwik Kit® highly visible. Our safety coating is applied on top of galvanization to ensure maximum corrosion resistance. Kwik Kit® exceeds OSHA and IBC standards and utilizes reliable Kee Klamp® or Kee Lite® safety components.Pre-assembled UprightsMake installation simple and quick with the pre-assembled uprights.Powder Coated Safety YellowHigh visibility safety yellow powder coating is used.Utilizes Engineered ComponentsMarket-leading and reliable Kee Klamp® or Kee Lite® safety components are used.Angle AdjustmentThere is a variable angle adjustment for step and ramp kits.Corrosion ProtectedOur safety yellow coating in applied on top of corrosion-resistant pipe for maximum protection.Safety IncludedSafety gloves are included for the installer's protection.Kwik Kit 6' Extension Kits are comprised of a 6-foot section of railing and an upright. This kit enables the extension of the Straight Kit and Corner Kit railings.Specifications:Pre-assembled uprightsUtilizes reliable Kee Klamp or Kee LiteTubing and fittings nominal 1-1/2 IPS (Pipe outside diameter is 1.90’’)Add 6' Total in length to standard Kwik Kits6' spacing between uprightsMeets or exceeds OSHA requirements for safety railings.
Kee Safety Kee Corner Kwik Kit Railing system, Kwik SCKee Corner Kwik Kit, Guardrail in a box. Includes Two (2) end uprights, One (1) corner upright, and four (4) 6’ horizontal rails. 6' spacing between uprights. Meets OSHA and IBC requirements. Visually appealing Rails powder-coated Safety Yellow, fittings galvanized. Highly corrosive resistant. Minimizes downtime in production environments.Quickly protect workplace areas and provide a safe environment with the Kwik Kit® railing. There is no need to weld or bend tubing because the pre-assembled uprights make installation speedy and simple. Safety Yellow coating comes standard, making the railing highly visible.Install the Kwik Kit® using a standard hex key to tighten the large, easy-to-use set screws. This simple hand tool is essentially all you need to create a sturdy railing system – there’s no welding or threading. And because your uprights are pre-assembled, installation is fast. By using a combination of our straight, corner and extension kits, you can achieve almost any standard railing configuration. Rails can also be cut where shorter sections are required and are available in both galvanized steel and aluminium. The safety yellow coating makes the Kwik Kit® highly visible. Our safety coating is applied on top of galvanization to ensure maximum corrosion resistance. Kwik Kit® exceeds OSHA and IBC standards and utilizes reliable Kee Klamp® or Kee Lite® safety components.Pre-assembled UprightsMake installation simple and quick with the pre-assembled uprights.Powder Coated Safety YellowHigh visibility safety yellow powder coating is used.Utilizes Engineered ComponentsMarket-leading and reliable Kee Klamp® or Kee Lite® safety components are used.Angle AdjustmentThere is a variable angle adjustment for step and ramp kits.Corrosion ProtectedOur safety yellow coating in applied on top of corrosion-resistant pipe for maximum protection.Safety IncludedSafety gloves are included for the installer's protection.Kwik Kit Corner Kits are composed of two 6-foot sections. You can extend the length of this corner railing through the use of an extension kit.Specifications:Pre-assembled uprights.Utilizes reliable Kee Klamp fitting.Tubing and fittings 1-1/2 IPS (Pipe outside diameter is 1.90’’)12' Total length6' spacing between uprightsMeets or exceeds OSHA requirements for safety railings
Kee Safety Kee Straight Kwik Kit Railing system, Kwik SSKee straight Kwik Kit, Guardrail in a box. Includes Two (2) end uprights, One (1) middle upright, and four (4) 6’ horizontal rails. 6' spacing between uprights. Meets OSHA and IBC requirements. Visually appealing Rails powder-coated Safety Yellow, fittings galvanized. Highly corrosive resistant. Minimizes downtime in production environments.Quickly protect workplace areas and provide a safe environment with the Kwik Kit® railing. There is no need to weld or bend tubing because the pre-assembled uprights make installation speedy and simple. Safety Yellow coating comes standard, making the railing highly visible.Install the Kwik Kit® using a standard hex key to tighten the large, easy-to-use set screws. This simple hand tool is essentially all you need to create a sturdy railing system – there’s no welding or threading. And because your uprights are pre-assembled, installation is fast. By using a combination of our straight, corner and extension kits, you can achieve almost any standard railing configuration. Rails can also be cut where shorter sections are required and are available in both galvanized steel and aluminium. The safety yellow coating makes the Kwik Kit® highly visible. Our safety coating is applied on top of galvanization to ensure maximum corrosion resistance. Kwik Kit® exceeds OSHA and IBC standards and utilizes reliable Kee Klamp® or Kee Lite® safety components.Pre-assembled UprightsMake installation simple and quick with the pre-assembled uprights.Powder Coated Safety YellowHigh visibility safety yellow powder coating is used.Utilizes Engineered ComponentsMarket-leading and reliable Kee Klamp® or Kee Lite® safety components are used.Angle AdjustmentThere is a variable angle adjustment for step and ramp kits.Corrosion ProtectedOur safety yellow coating in applied on top of corrosion-resistant pipe for maximum protection.Safety IncludedSafety gloves are included for the installer's protection.Kwik Kit Straight Kits are comprised of two 6 foot sections for a combined length of 12 feet. You can extend the length of this railing through the use of an extension kit.Specifications:Pre-assembled uprights.Utilizes reliable Kee Klamp fittings.Tubing and fittings 1-1/2 IPS (Pipe outside diameter is 1.90’’)12' Total length6' spacing between uprights.Meets or exceeds OSHA requirements for safety railings
Kee Safety Kee Universal Self-Closing Gate, SGNA500GVAdjustable Kee Universal Self-Closing Gate. Covers openings from 16" to 44". One gate fits all openings – simply cut onsite, galvanized finish.A fully adjustable range of self-closing safety gates for use in rooftop or industrial environments. Safety gates are ideal for protecting any openings, ladder/stair access points, roof hatches, walkways, access to industrial machinery and other restricted areas, where regular access for maintenance and inspection is needed. Our gates are spring-loaded so will automatically close behind the user. Spring-loaded safety gates are considered the preferred solution to chains, bars or sliding tubes when protecting these areas as they automatically close behind a person, overcoming the problem of human error.Spring LoadedOur gates are spring loaded so will automatically close behind the user.Finish OptionsAll safety gates are available in galvanised steel finish or yellow powder coated.SimpleThey are quick and easy to install which saves time and money.AdjustableThe width can be cut to size on-site so they can be adjusted as neededVersatileCan fit different surfaces (round or square) and can be used for external and internal applications.Specifications:Covers openings 16"-44"Complies with OSHA 29 CFR 1910.28 and 1910.27Integrates with existing openings and ladder waysEasily installed with hand toolsThird-party testedOne gate fits all openings –simply cut onsite
Kee Safety Kee Universal Self-Closing Gate Powder coat yellow, SGNA500PCAdjustable Kee Universal Self-Closing Gate. Covers openings from 16" to 44". One gate fits all openings – simply cut onsite. Powder coated safety yellow finish.A fully adjustable range of self-closing safety gates for use in rooftop or industrial environments. Safety gates are ideal for protecting any openings, ladder/stair access points, roof hatches, walkways, access to industrial machinery and other restricted areas, where regular access for maintenance and inspection is needed. Our gates are spring-loaded so will automatically close behind the user. Spring-loaded safety gates are considered the preferred solution to chains, bars or sliding tubes when protecting these areas as they automatically close behind a person, overcoming the problem of human error.SpringLoaded Our gates are spring loaded so will automatically close behind the user.Finish OptionsAll safety gates are available in galvanised steel finish or yellow powder coated.SimpleThey are quick and easy to install which saves time and money.AdjustableThe width can be cut to size on-site so they can be adjusted as needed.VersatileCan fit different surfaces (round or square) and can be used for external and internal applications.Specifications:Covers openings 16"-44"Complies with OSHA 29 CFR 1910.28 and 1910.27Integrates with existing openings and ladder waysEasily installed with hand toolsThird-party testedOne gate fits all openings –simply cut onsite